Відео

What was the issue ??? I have similar but mine is milder and can be heard only on one side

If I am not mistaken, will this video also work for a 2014 Yamaha Bolt? I am under the impression that they have the same motor, just different body styles?

I have a 2000 vstar and i cant seem to find neutral!! I play around with the shifter andntry and start my 1100 but no neutral light goes on and cant get it to start!!!! What the hell !!!!!!!

I was about to use a DA and destroy the sticker since I'm changing color .. this takes hours out of my planned process.. thank you very much for making this video

Still the only video in 2024 I could refer to. Thanks boss

Good solution for when the gas tank is off the bike, and tuning the carburetor

How oftem am I supposed to breathe the bottle sir

I’ve never restored anything but want to restore a 2000 VSTAR 650 that’s been sitting in the desert sun for about 12 years. Any tips for me? Is it worth it?

Thank you for this Maustarman!

Im trying to do that same thing on a 2009 polaris sportsman. Its plastic obviously. Im worrying about scratching the plastic and seeing the outline. Anyone have suggestions?

Thanks! Great advice!

Music too loud couldn’t hear hat you were saying in the second half.

Thank you for sharing

I did the same thing on a Suzuki drz gas tank but only using the exacto knife and a hair dryer no wd-40 same result they came off

Why two hipercharger total useless?! Why????!!!!

Where's part 2?

most helpfull video i have found thank you

Question what did you use to clean everything do nice. also do you put the gasket as is on the two clean surfaces nothing else?

Where did you order the cams from

Skip the wd ...

Thank you for this video!

Man why do you and so many other folks posting informative info not make sure your audio is where we can hear it and i mean hear the whole video not just part of it. Did you not watch it b4 it was posted? We cant even hear the very beginning of what you're saying. Im working on same project but i cant waste time watching and not able to hear you so plz remember this b4 you post your next video plz. Not trying to down you.. im just saying

basically you put loud music over 70% of what you were talking.

Great video, I was waiting for you to fire her up: otherwise very good job

Amazing video! Thank you. Can you please send me the link to the video of you installing the engine? I'm doing mine right now and can really use the assistance!

after 12 years, still the best tutorials for this work. thanx!

Great video.

I tried this on my 08 Vstar 1100 . I successfully installed the .33 ohm resistor . I installed 4 led bulbs in the stock turn signals and now the turn signals don’t work in the back at all , the front stay on solid. Any suggestions would be greatly appreciated 🙏🏼

I just bought a 2002 Vstar today. So really, all I have to do is switch the tubing to close it off right? Everything else is not necessary and only for looks and cleanliness?

You should put a disclaimer you have to have the hands of a surgeon for this technique and your better off block sanding with 600 till you hit the sticker and then use the blower

Great idea. The ONLY thing I would do different would be to tighten the on off valve really tight to the reducer and THEN epoxy it to the tank to prevent cracking the JB weld.

I got a 2020 ElectraGlide Harley. It has the bar and shield logo decal on each side of tank, it’s red and under clear coat. I want it removed. Do you have any experience on removing Harley decals? Fyi: I have patience and time so if you say do it I will. And of course if I mess up it’s not your fault.ps: I have a metal emblem to replace.

Should have no music.. then start talking about the useless part. Talk about the kickstand and the gasket for 5 minutes not anything needed

What bags and how?

I wanna hear it.

You're a fkn idiot dude. Damn, I really need to start making videos on how to do shit right. DO NOT TAKE YOUR EXXAUST OFF

do not use red locktight on something like this, use blue. red is going to cause more problems down the road if u ever need to remove that part again. it takes 500 degrees to melt red lock tight so u can remove the bolt.

Couldn't you use a 1-gallon thinner can?

Yasser is the music for me main

Does this fix all the issues when ya change to led?

Can the cam be moved so that it is timed well? I did my starter clutch and i turned the motor so many times to get it in line and it never lined up, my bike isnt as strong as my buddies either and i was thinking the timing is off

Sounds like the editor had one to many "refreshments" music was too loud but pretty good video besides that thank you

Thanks!!!

Hi guys it's only for carburetor, not for FI system

What part number is this screws

Did you ever figure it out?

You may dissolve the white sticky edging with some cellulose thinners on a rag. That way you don't need to use sandpaper.

Why the incredibly annoying music?

When you're making a how to video, don't play music over the instructions !!! 👇😡👎

Tried this with no results don’t know where it went wrong. All 4 still flash no matter what